FrSky Tx and Rx Systems HiModel Page 4 Review

HiModel

FRSKY AMPERE SENSOR FAS-100

Model	FAS-100
Dimension	38 x 30 x 10mm
Weight	24g
Measurement range	0-100A
Maximum safe current	100A
Sensor current consumption	33mA
Update rate	≥1Hz

, , , , , , Specifications:, , , , , , , , , , , * When use the amp sensor FAS-100 with a sensor hub, please make sure your sensor hub firmware is V2.0., , ,

Includes/Requires: Includes:1 x amp sensor

HiModel

FRSKY TWO-WAY 2.4G MODULE W/LCD DISPLAY DHT-U

Operating Voltage Range	6.0V-13.0V
Operating Current	50mA
Output Power	60mW
Resolution	3072 (>11bit)
V8 _Mode	Non-telemetry receivers (V8FR-HV, V8R7-HV, V8R7-SP, V8R4)
D_Mode	Telemetry receivers (D8R, D8RSP, D6FR, D4FR)

, , , , , , Specifications:, , , , , , , , , , , Specification, Compatibility:, , ,

Features: Features 1) All-in-one combination of telemetry module,in-built display and ...

HiModel

FRSKY 2.4G 5-CHANNEL TWO-WAY RECEIVER (NANO JST CONNECTOR) VD5M

Dimension	21165.8mm
Weight	2.0g
Operating Voltage Range	3.0V-7.2V
Operating Current	20mA
Operating Range	>300M

, , , , , , Specifications:, , , , , , , , , , , 2.4GHz Two Way Series, Number of Channels: 5, Bind procedure:, 1) Ascertain that the transmitter is in the PPM mode. Turn the transmitter off., 2) Turn on the transmitter while holding the F/S button on the transmitter module. Release the button. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind to the receiver., 3) Connect the provided binding cable to corresponding channels of VD5M (see 1.1 Compatibility chart for details), and connect battery to the receiver. LED on the receiver will flash, indicating the binding process is completed. Turn off both the transmitter and receiver, and disconnect the binding cable from VD5M., 4) Turn on the transmitter and connect the battery to the receiver. The RED LED on the receiver will indicate the receiver is receiving commands from the transmitter., The receiver/transmitter module binding will not have to be repeated, unless one of the two is replaced., Note: Make sure corresponding channels are connected by provided binding cable when working with the transmitter module., , ,

Features: Features 1) Lighter weight and physically smaller than D8R-II ...

3 Reviews

HiModel

FRSKY 2.4G 6-CHANNEL RECEIVER (NANO JST CONNECTOR) TFR6M

Dimension	31237mm
Weight	3.4g / 2.7g (naked)
Range	3.5V~10V
Operating Temperature Range	-10℃~60℃
Ground Range	>300m
FASST 2.4G Air Systems (7CH Mode/Multi Mode)	6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc.

, , , , , , Specifications:, , , , , , , , , , , Number of Channels: 6, Operating Voltage, Compatibility:, , ,

Features: Features: 1) Lighter weight and physically smaller， designed for ...

HiModel

FRSKY 2.4G 7-CHANNEL RECEIVER HIGH VOLTAGE VERSION V8R7-II HV

Operating Voltage Range	3.0V-16V(HV Version)
Operating Current	30mA
Resolution	3072
Latency	22ms
Specified	V8R7 (7CH, 7.5g, 40mm×21mm×10mm, 1.5km-2.5km)

, , , , , , Specifications:, , , , , , , , , , , , ,

Features: ◆ Advanced Continuous Channel Shifting Technology ( ACCST SYSTEM), ...

2 Reviews

HiModel

FRSKY 2.4G 8-CHANNEL RECEIVER HIGH VOLTAGE VERSION V8FR-II HV

Operating Voltage Range	3V-16V
Operating Current	30mA
Specified Range	1.5km-2.5km(under factory testing conditions only)
Resolution	3072
Latency	22ms
Number of Channels	8CH
Dimensions	49mm×24.5mm×15 mm
Weight	14g

, , , , , , Specifications:, , , , , , , , , , , , ,

Features: ◆ Advanced Continuous Channel Shifting Technology ( ACCST SYSTEM), ...

2 Reviews

HiModel

FRSKY 2.4G 8-CHANNEL RECEIVER W/PPM OUTPUT V8R7SP

Model	V8R7-SP
Operating Voltage Range	3.0V-16.0V
Operating Current	30mA
Resolution	3072
Latency	22ms
Specified	7CH, 9g, 49mm×23mm×12mm, 1.5km-2.5km
Warning	DO NOT connect servos to channel 8, otherwise servos will get hot or even burn out.

, , , , , , Specifications:, , , , , , , , , , , V8R7-SP improves the smoothness of high-speed digital servos., Bind Procedure:, 1) Turn on your transmitter and switch it to PPM mode, turn off the TX., 2) Turn on your transmitter while holding the programming button. Release it a few seconds later. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind the receiver., 3) Connect the battery to the receiver while holding the receiver’s F/S button. The LED on the receiver will flash, indicating the binding process is complete. Turn off the transmitter and receiver., 4) Turn on your transmitter. Connect the battery to the receiver when ORANGE LED on TX is on. The LED on the receiver will indicate the receiver is receiving commands from the transmitter. In a few seconds system is ready to work (communication is established)., Binding is required only to set up a new link (like new or additional receiver or transmitter module). To control multi-receivers, every receiver should be programmed with the transmitter in binding state., Failsafe:, V8R7-SP supports failsafe function for all channels. Just do it as bellow:, After the receiver has been bind, press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, the failsafe is set up successfully., If you do not need the failsafe function any more, just re-bind the receiver., , ,

Includes/Requires: Includes:1 x V8R7SP receiver

HiModel

FRSKY LIPO VOLTAGE SENSOR FLVS-01

Model	FLVS-01
Dimension	45217mm
Weight	5.2g
Measurement range	1S~6S (The first lipo voltage should be more than 3.55V)
Cell voltage display range	0.20~4.20V
Voltage display resolution	0.01V
Voltage detection precision	0.03V
Current of the board	15.5mA
Operating temperature range	-30℃~70℃
Pixel	128*64 with OLED display screen

, , , , , , Specifications:, , , , , , , , , , , Specifications:, ﹡Note:, To make the FLVS-01 works with sensor hub and FLD-02/DHT-U to display total voltage and cell voltages as connected, you may need to upgrade your firmware of sensor hub and DHT-U to version 2.0, refer to included instruction manual for details., , ,

Features: Different sensors facilitate to monitor different data, such as ...